Wednesday, January 10, 2018
New A Frame Plan for 2018
We have received a lot of requests for A Frames over the past few years so we are replacing our plan 4 with A frames. The pricing will be on our website very soon but here is a sample. This is a 16 x 20 model with a base price of $20,500. These will also be offered in DIY Kits as well. We are going to have larger sizes as well which we will be posting on our website as soon as we get the pricing updates finished.
Subscribe to:
Post Comments (Atom)
6 comments:
(2c)...space-elevator (orbital station ramp)... "air-toilet-bidet"... SAFETY OF INSTALLERS AND USERS: Installation must only be carried out by qualified persons, following the instructions of each apparatus. Make sure that the installation complies with each country´s current Sanitary, Mechanical and Electrical Norms. SECURITY:"ALL ELECTRICITY INSIDE BATHROOM to 12 V.CC, switch, lights, etc". Outside bathroom a Box-control with fuses, relays 12 v.cc/220 v.ac, timers, etc. Ventilator of Pressure (220 v.ac/50 W): "Always Placed Outside of the Bathroom", but into house. Extractor Mode, placed at wall´s top. Injector Mode, placed at wall´s down: Injecting at floor level by tube Air from house; Installation simple, only one switch inside bathroom for on/off ventilator. Or also can be all automated: in Injector Mode, a push-button on door for stop ventilator when open the bathroom´s door. More automatism, other push-button detecting weight, presence´s sensor; air-toilet-bidet motorized (12 v.cc) and totally automated: timer on/off, 2 sliding in horizontal semicircles close-fasten/open release the plastic-bag, automatic fast plastic-bag´s closing e.g. by thermo-soldering and its exit to exterior-tank, etc.
(2b)...space-elevator (orbital station ramp)... Still there are in polar areas people with outdoor toilets supporting -40 ºC temperature...come on, is easy make more simple (only by qualified persons) this "air-toilet-bidet", ###(1)### made with a stainless steel SINK subject riveted (6 stainless steel rivets of 4x10 mms) over an, in white angle (mms: 40x40, 30x30, 20x20), ALUMINIUM STRUCTURE 34 cms in height, here Al. rivets 4x15; at rear´s part below 2 little wheels for a few and limited sliding for exit from narrow corner for using bidet; ###(2)### a little PLASTIC BAG (25x30 cms) put "inside" of a PVC #TUBE 5 cms in length and 13 cms in diameter, with the plastic-bag Fastened with a vulgar slim circular RUBBER-BAND (2x90 mms) around by outside of the #TUBE´s top, ←###(3)### on this at the top and glued, PVC adhesive, also by outside, one "open" (cut) PVC RING° (1 cm length and also 13 cms in diameter) for plastic-bag No sliding when it is Fastened here with the Rubber-Band, ###(4)### and also it° serves how buffer-touching over other PVC **ring-support (made from a Cap that have 16 cms in exterior diameter, making to it a central circular-cut of 13.5 cms in diameter and cutting after at 2.5 cms length: final **ring-support sizes cms=ø16xø13.5x2.5) **placed (ø16 up surface level/ø13.5 down) and glued (wood white-glue) into circular cut=16 cms in diameter of ◘plane, for that the #TUBE no fall down; ###(5)### this #TUBE there is Installed Removable into ◘plane (surface mus be flat) at center of a normal "(wood) #ring-cap-toilet" subject ((←this is elevated with 2 plastic buffer, doors, of 2.5 cms screwed at both sides under #ring´s front and also under rear other 2 supplement of 2.5 cms length made from 2 PVC caps of 6 cms in diameter, placed under the 2 normal #ring´s subjection-screws, for #ring stay horizontal)) over the Sink´s structure; ###(6)###→
(2b2)...space-elevator (orbital station ramp)... →###(6)### under the #ring a plywood ◘plane 1.5x34x21 cms "made all waterproof and stainless" ((rear´s ◘plane wide must be cut away for it no protrude from the surroundings under #ring: ◘plane´s wide cms, front=34, rear=28, the figure now has 6 edges, cms: 34,14,8,28,8,14)) both faces covered, up with methacrylate 2 mms thick, down white Aluminium Sheet 0.8 mms thick, and ◘plane´s edges covered with U-aluminium of 2 cms (or some more wide according to the final edge´s thick "metha+plywood+Al"), each edge with its U-aluminium subject with 2 stainless steel rivets of 3x8 mms on the down-face of white Aluminium Sheet: "now the ◘plane has 6 edges", 6 U-Al and 12 rivets, (make first the figure with cardboard for testing); ◘plane subject with 6 wood-screws of stainless steel (5x30 mms) under #ring "from half backwards, ◘plane with Central Circular Cut=16 cms in diameter for put the removable #TUBE from surface downwards; and few more for adjusting all. ###(7)### Used plastic-bags, "closed with a knot", are put down for a placed apart "PVC tube (9 cms diameter) through the floor or wall" with indoor removable PVC cap, falling, "outside of the house", into a little portable Tank of aluminium or plastic, into the Tank some of water and lye, being the plastic-bags soon eliminated after adequately. According to each case, LIQUIDS can be eliminated by tube through the floor or wall to "other" exterior portable plastic-tank e.g. a big empty lye bottle, or also falling into SINK´s interior to a portable little plastic-container (made e.g. from big lye bottle cutting with scissors) inside and/or under the air-toilet-bidet; (after each use: tanks, tubes, and all always clean and shining how new, and air-toilet-bidet dry prepared for the next use). One powerful (220 v.ac/50 W) cylindrical Ventilator of Pressure "Placed Outside of the Bathroom", but into house Injecting at floor level by tube ø15 cms (till wall´s corner "behind and under" the air-toilet-bidet) Air from house in that little Bathroom Indoor ~1 mt², also little washbasin (e.g. other sink), shower, etc. (Inside the Bathroom ALL to 12 v.cc); with little window, or roomy tube, near ceiling exiting the air to house´s exterior; and made with 2 wood-walls airtight in a house´s inside corner; never more freezer cold, bears...
Post a Comment